---
title: "How it works: NUNA"
description: "A mesh of sensor nodes that sleep between scheduled slots, reroute around a failed relay on their own, and share one uplink out of a remote field site."
url: https://howitworks.nunasystems.com/
---

How it works

A sensor network in the Arctic fails for boring reasons. Batteries run flat, a relay dies unnoticed, and nobody finds out until the next field season. The design answer is a radio that knows exactly when to wake up.

01 / The network

Sensor nodes talk to a nearby relay. Relays forward toward a single gateway, which is the only device needing a connection to the outside world. One uplink serves the whole site.

C1 · sensor Carries the instrument. Talks to one parent and never forwards anyone else’s traffic.

C2 · relay Forwards across the mesh and acts as cluster master for the sensors around it.

C3 · gateway The sink for all data and the source of network time. Backhaul is whatever the site has.

Mesh topology

Three roles, one set of hardware

02 / Why it lasts

Most low-power radios waste their battery waiting for something to arrive. Every node here is given a precise slot, so it wakes, does its business and goes back to deep sleep. Nothing idles with a receiver open.

Scheduled A time-division schedule gives every node its own wake, transmit and sleep window.

Guard bands Each slot is padded for clock drift, measured across temperature rather than assumed.

Deep sleep The sensor rail is switched off between samples, so an attached instrument draws nothing.

Slot schedule

One reporting cycle, radio on for roughly 100 ms

03 / When something breaks

Every node keeps a list of the other relays it has heard from. When its parent stops beaconing, it promotes one of them and re-registers. There is no manual topology file and no site visit.

Beacons Relays announce their identity, position in the tree and routing cost.

Power aware Routing cost is not hop count. A relay whose battery is falling advertises a rising cost, so traffic moves to healthier nodes.

Ages together Because load shifts away from depleting relays, the network degrades evenly instead of losing one hotspot at a time.

Parent failure

A failed hop is replaced from the neighbour list

04 / Power-aware routing

A relay advertises what it costs to send through it, and that cost rises as its battery falls. When a relay runs low, the nodes around it send their readings another way. Once it has recharged, it is the cheapest route again and the traffic comes back.

Beacons Every beacon carries the relay’s current routing cost, so neighbours choose on up-to-date numbers.

Battery A falling battery raises the cost a relay advertises. Nothing is switched off by hand.

Recovery A relay with a solar input recharges between reports, then rejoins the cheapest route on its own.

Power-aware routing

A relay runs low, traffic moves away, then returns once it has charged

05 / Pricing a hop

Routing cost is not hop count. Each link is priced from how far the signal has to travel, how much battery the receiving relay has left, and how many hops remain to the gateway. A node adds up the price of each route it could take and sends along the cheapest.

Distance A longer, weaker link costs more than a short, strong one.

Battery A relay with less energy in reserve charges more to carry traffic.

Hops left Every extra hop to the gateway adds to the price, so shorter routes are preferred.

Pricing a hop

The nearer relay is low on battery, so the route through the other is cheaper

06 / Joining

1. ### Discovery
   
   It listens for relay beacons, picks a parent, and keeps every other relay it heard as a fallback.
2. ### Join and slot assignment
   
   It registers with that parent and is given a slot. From here the radio schedule is fully determined, so there is no reason to open a receiver at any other time.
3. ### Synchronised operation
   
   The gateway is the time anchor, and time propagates down the tree. Slots stay aligned as the hardware warms and cools.

Joining the network

07 / The hardware

A C1, a C2 and a C3 are the same hardware in different configurations, so a deployment is one part number to build, stock and repair. Instruments connect over the interfaces operators already have, rather than requiring a new capital base of probes.

![The assembled V1 board, green, with terminal blocks along its edges and an antenna cable attached](https://howitworks.nunasystems.com/assets/photos/v1-board-assembled.jpg)

_The V1 board, assembled_

![Close-up of the antenna connector and the 868 MHz radio section of the V1 board, with a spectrum trace on an instrument behind it](https://howitworks.nunasystems.com/assets/photos/v1-rf-section.jpg)

_The 868 MHz radio section during RF testing_

![The bare V1 circuit board before assembly, showing gold pads and silkscreen labels for the battery, sensor and power sections](https://howitworks.nunasystems.com/assets/photos/v1-bare-board.jpg)

_The bare V1 board before assembly_

- Validated in a climate chamber to -40°C.
- One board set, configured as sensor, relay or gateway.
- 868 MHz, license-free across the EU and Greenland.

Three roles, compared

C1

### Sensor

Carries the instrument.

Traffic Sends its own readings and never forwards anyone else’s

Place in the tree Talks to one parent

Network time Takes time from its parent

Uplink Not applicable

C2

### Relay

Forwards across the mesh.

Traffic Forwards toward the gateway

Place in the tree Cluster master for the sensors around it

Network time Passes time down the tree

Uplink Not applicable

C3

### Gateway

The sink for all data.

Traffic Receives every reading on the site

Place in the tree The single way out

Network time The time anchor for the whole network

Uplink Whatever the site has

Hardware The same board set in all three roles

Inside one node

In each reporting cycle radio on for roughly 100 milliseconds
Enforced in firmware, not left to the operator a duty cycle of 1 percent
ETSI M-band, license-free in the EU and Greenland 868 megahertz
Measured across temperature in the chamber 0.03 parts per million

Shared by all three

Compute and radio STM32WL55, application core and sub-GHz transceiver on one die

Sensor ports SDI-12, RS-485, two analog inputs and a switched excitation channel, on Phoenix Contact headers that take more than 100 connector types

Power Solar MPPT or USB-PD, with a 4S Li-ion pack and a power-gated sensor rail

08 / Honestly

The hardware has been validated in a climate chamber to -40°C, where over 98% of about 19,600 packets were acknowledged and the crystal clock held to 0.03 ppm. That is a measurement.

Field life, coverage and range are modelled from component behaviour and have not been observed over a season in the field. We publish them as design targets, marked as such, and will replace each one with a measurement. The first field deployment is planned for summer 2027.

Every figure, in one place

Measured values and V2 design targets, side by side and labelled.

[See them on the comparison page](https://howitworks.nunasystems.com/compare#measured)

---

NUNA, DTU Skylab, Lyngby, Denmark. contact@nunasystems.com
